Features of Load Indicator & Controller

• Micro-Controller based system with seven segment display (0.56”), single/double row & 6 digit interface & 5 keys.
• Displays the process value & peak value.
• Provision for manual resetting the peak value.
• (0-15mV) read as 0-99,999 Counts with 1 count resolution – 24 bit ADC –10 SPS or 80SPS.
• Any range of load cell can be interfaced (+5V to +24Vexcitation)
• Digital Calibration (TARE & SPAN) – No trim Pot.
• Auto Zero for 3counts.
• 0-10V output for zero to full scale (suitable for PLC systems) with 10mV resolution.
• 2 Relay outputs (7A Amps rated) for 2 Setpoints with Hysteresis, through keypad entry.
• Decimal Point selection.
• Power on Tare / Manual Tare Programmable.
• Programmable Resolution 1count, 2counts, 5counts & 10counts.
• Programmable Over range load limit.
• UP (Peak Reset) key, Down Key, Shift key, Enter Key & Tare Key are the 5 different keys provided.
• 230V AC input power supply with Fuse (500mA) protection.
• Compact 48x96x110mm panel mountable plastic enclosure for industrial application.
• System can be custom built to measure 4-20mA (pressure), length measurement (Potentiometer type), Counting Scale & any low level voltage measurement.

Various Products related to Load & Pressure:

• Tensile Strength Indicator & Controller.
• Spring Testing Machine – Load & Length Measurement.
• Batching Plant Controller with 8 relay outputs, based on load.
• Load Controller with fast sampling (80SPS) for conveyor sort of applications.
• Counting Indicator & Controller with high accuracy.
• Load Indicator with programmable RS485 address.
• Load Indicator with analog output, (0-5V or 0-10V) with 5mV & 10mV accuracy.
• Load Indicator with 4-20mA output.
• Load Indicator with PC Calibration, through RS232 .
• Load Indicator with data logging (NVSRAM).

Features of Counter & RPM Indicator

• Micro-Controller based system with seven segment display (0.56”), single row & 6 digit interface & 5 keys.
• PNP or NPN Sensor Interface or Potential Free Contacts (+12V/60mA Isolated).
• Programmable Preset – 6 digit.
• With internal Digital noise filter – To avoid industrial noisy condition.
• 2 Relay outputs (7A Amps rated) with high & low setpoints.
• RS232 link / RS485 with programmable slave address.
• UP key, Down Key, Shift key, Enter Key & Reset Key are the 5 different keys provided.
• 230V AC input power supply with Fuse (500mA) protection.
• Compact 48x96x110mm panel mountable plastic enclosure for industrial application. (1inche, 2 inche, 4 inche also available).

Counter:

• Memory Back up for the final reading.
• High Frequency Counting – 5KHz
• External Start Command / Reset Command.
• Jumbo Display counters – 4,5 & 6 digit.

RPM Indicator:

• a. High Frequency – 3KHz – One Pulse per rotation.
• b. Averaging.
• c. 0-10V output for zero to full scale (suitable for PLC systems) with 10mV resolution.

Note: System can be custom built to 7 digit or 8 digit counter.

Features of Length/Angle Measurement – Incremental Encoder

• Micro-Controller based system with seven segment display (0.56”), single row & 6 digit interface & 5 keys.
• Totem Pole or NPN or Line Driver Encoder Interface (+12V/60mA Isolated) or (+5V).
• A, B & Z pulse sensing – in built QEI Interface.
• Programmable ppr & Distance entry for one revolution (user entry).
• Programmable Preset Length or Angle.
• With internal Digital noise filter – To avoid industrial noisy condition.
• Memory Back up for the final reading.
• 0-10V output for zero to full scale (suitable for PLC systems) with 10mV resolution.
• 2 Relay outputs (7A Amps rated) with high & low set points.
• RS232 link / RS485 with programmable slave address.
• UP key, Down Key, Shift key, Enter Key & Reset Key are the 5 different keys provided.
• 230V AC input power supply with Fuse (500mA) protection.
• Compact 48x96x110mm panel mountable plastic enclosure for industrial application.

Note: System can be custom built for any process control equipment like motor control.

Features of Linear Scale DRO

• Micro-Controller based system with seven segment display (0.56”), single row & 8digit interface & 7 keys for each axis.
• Linear Scale of any range 100mm to 1000mm.
• TTL compatible, +12V Logic Signal, Sine Voltage Input or 11uA Current Input:
• Sensing A pulse & B pulse. (no Z pulse sensing, if required can be interfaced for home position)
• Programmable – Plus or Minus (for direction selection) – Individual LED Indication.
• Programmable – Inches or mm selection – Individual LED Indication.
• Programmable – DIAMETER or RADIUS selection-– Individual LED Indication.
• Programmable – Half function -– LED Indication.
• Software – Linear Error Full Scale Calibration (+/-25%) for the error reading.
• Zero reference selection or Required value reference selection.
• Memory backup for the final reading.
• 2 Relay outputs (7A Amps rated) – Used when length limit is required.
• RS232 link (Optional) – RS485 with slave address.
• mm/inches key, rad/dia key, UP key, Down Key, Shift key, Enter Key & Zero/Reset Key – 7 different keys provided. (Optional external Start/Stop toggle switch)
• 230V AC input power supply- Filter, Switch & Fuse (3A) protection.
• Rigid metal enclosure for industrial application.
• System can be custom built, according to customer requirement.

Features of Temperature Indicator & Controller

• Micro-Controller based system with seven segment display (0.56”), single row & 4 digit interface & 5 keys.
• Thermocouple, PT100, Current/Voltage output Sensors.
• Compensation for Thermocouples.
• High Accuracy & Stability.
• 2 Channel, Differential Controllers with timers.
• 2 Relay outputs (7A Amps rated) with set point & hysteresis.
• RS232 link / RS485 with programmable slave address.
• UP key, Down Key, Shift key, Enter Key & Reset Key are the 5 different keys provided.
• 230V AC input power supply with Fuse (500mA) protection.
• Compact 48x96x110mm panel mountable plastic enclosure for industrial application.

Note: System can be custom built according to customer requirement.

Features of DC Drive – SCR Control

• Microcontroller based SCR phase angle control Drive for DC motors.
• Rating: <=1.0HP, Single Phase, 230V AC, 50Hz with 6A Fuse (strictly no to square wave inverters & generators without 50Hz).
• Applicable for DC Motor Shunt or Compound.
• Armature Voltage – (0-200V, 4.5A).
• Armature Overload Protection - Programmable Armature Current – (0-5A), using keypad.
• Field Voltage terminated – 200V DC.
• Field Disconnect protection – Programmable.
• 3 seven segment displays & 4 keys (UP, DOWN, ENTER & AC voltage monitor).
• 1 setpoint – PER– in terms of percentage (0-99% with 1% resolution).
• One external digital input status, decides ON or OFF.
• Programmable Acceleration (dL1) & deceleration (dL2): 0-5000 millisecs.
• Programmable Percentage limit (P.Lt).
• Input AC voltage measurement and display.
• Compact panel mountable plastic enclosure of size: 96x96x110mm with terminals.

Note: System can be custom built for any process control equipment like vibration controller, spot welding units using SCR packs.

Features of Industrial & Commercial Timers

• Micro-Controller based system with seven segment display (0.56”), single row & 6 digit interface & 5 keys.
• Cyclic ON/ OFF Timer or ON Timer.
• Programmable ON/OFF Timer in terms of 59min & 59 seconds (max).
• 2 Relay outputs (7A Amps rated).
• External START/STOP & RESET Command.
• Memory Back during power failure.
• RS232 link / RS485 with programmable slave address.
• UP key, Down Key, Shift key, Enter Key & Reset Key are the 5 different keys provided.
• 230V AC input power supply with Fuse (500mA) protection.
• Compact 48x96x110mm panel mountable plastic enclosure for industrial application.

Real Time Clock Alarm Timers:

• LCD based alarm unit with 24 different time settings for schools & office.
• LCD based alarm unit with audio mp3 output for temples, mosques & churches.

Note: System can be custom built according to customer requirement.

Features of Fire Alarm Panel

• uC based system with 2 Line, 16 Character LCD, LED indications & 8 keys.
• Single Power +16V SMPS supply & +12V Battery. Conventional Smoke Detector Interface +24V.
• Two or Four Zones (Selectable) with 20 smoke Detectors per zone.
• 4 Relay outputs – Switched On during fire conditions & during manual evacuate.
• Sensor Detection – Open, Short, Normal & Fire.
• 8 Keys – Reset, Evacuate, Accept, Test, Menu, Isolate, Shift & Enter.
• RS232 Link. (Optional).
• Local Buzzer to indicate system condition.
• SMPS based power supply with 3A current rating – Can supply 2A to the outside Hooters.
• Battery Operated with charging at 350mA.
• LED Indications – Sensor Open, Sensor Short, Sensor Fire & Sensor Isolate. AC ON/OFF, Battery ON/OFF, Battery Charging, Low Battery.
• LCD Indications - Sensor Open, Sensor Short, Sensor Fire & Sensor Isolate. AC ON/OFF, Battery ON/OFF, Battery Charging, Low Battery.
• Three detachable Boards – CPU Board, Power Supply Board & Zone input & Relay output board, Easy to service.
• Latest SMD technology.

Note: System can be custom-built, according to the customer requirement.

Features of DDS Function Generator

• Compact uC based system with 2 Line LCD interface & keypad (4 keys) and two potentiometers.
• Settable frequency from 0-1MHz with a resolution of 1Hz in all ranges.
• Potentiometer-1 used for Coarse Tuning & Potentiometer-2 used for Fine Tuning of the frequency setting.
• Four Keys – UP Key, DOWN key for Range Selection, Waveform Select key & Enter key.
• Following table consist the range selection, with accuracy & resolution:



S.No	Range Selection	Potentiometer-1 Range – Coarse Tuning	Potentiometer-2 Range – Fine Tuning	Accuracy	Display Resolution
1.	0-10Hz	0-10Hz	-	+/- 1Hz	+/- 1Hz
2.	10-100Hz	10-100Hz	-	+/- 1Hz	+/- 1Hz
3.	100-1000Hz	100 – 990Hz	0-10Hz	+/- 1Hz	+/- 1Hz
4.	1KHz-10KHz	1KHz – 9900Hz	0-100Hz	+/- 1Hz	+/- 1Hz
5.	10KHz-100KHz	10KHz – 99KHz	0-100Hz	+/- 1Hz	+/- 1Hz
6.	100KHz-1MHz	100KHz – 900KHz	0-1000Hz	+/- 1Hz	+/- 1Hz



• Selectable Sine & Triangle Waveform. Square & Pulse waveform can be generated by using additional circuits using sine or triangle.
• Maximum Amplitude of 4.50V. (also can be increased by additional circuits)
• Amplitude Display on LCD. (0-5V or 0-15V according to specification).
• Unit working with +5V/ 100mA.

Features of Remote Control Units

• Compact uC based system for remote applications.
• Infra Red Based Remote Control – Used to switch ON/OFF the lights and to adjust the speed of the fan(NEC & RC5).
• Infra Red Based Remote Control – Used to set the score card remotely (NEC & RC5).
• Radio Frequency Based Remote Control – used to control the lighting of a camera, during flash.

Note: System can be custom-built, according to the customer requirement.